Search Results

Search results for "3-2"

Electrical Connector 2P+E Industrial Form B without circuit IP65 0-250v

EN 175301-803 (DIN43650B) Industrial Form Hirschmann Connector, 11mm between pins\nGland: PG9 for cable diameter 6 to 8mm \nVoltage: 0 to 250 Volts\nResistance: 4 mOhm Max\nCurrent: 10 Amps max (without circuit), 1 Amp maximum with circuit. \nConnection: DIN43650B industrial form is with PG9 cable entry for 6 to 8mm\nGasket: NBR\nProtection: IP65\nWire connection: clamping contact. \nOption: conduit entry 5 to 6mm or 1/2 NPT conduit entry, with LED, with VDR varistor and Rectified \n\n2022 new terminal block\n\nIn order to establish a suitable electrical connection, the use of ferrules for fine stranded cables are mandatory. Be aware that the wire (conductor) cross-section affects the maximum current load (Amp) capacity.

2247 in stock Model: DIN1

1/4 Brass Solenoid Valve 0-8.5Bar 2/2 Normally Closed 2.3mm PU220AR-02

1/4 Brass solenoid valve Shako PU220AR-02 ®\nFunction: 2/2 way normally closed \nOperation: direct acting\nPort: 1/4 BSP, option NPT thread\nPressure: 0 to 8.5 Bar (AC) or 0 to 7 Bar (DC Voltage)\nBody: Brass\nInternals: stainless steel\nSeals: NBR standard, option FKM, EPDM or HNBR\nMedia: air, water, vacuum, light oils and any other gases and fluids under 40CST that are compatible with the materials of construction.\nOrifice: 2.3mm\nKv flow factor: 2.0 L/Min based on water with 1 Bar pressure drop.\nCoil: low power 4.5 watt IP65 Class F DIN43650B 100% duty rated\nProtection: IP65 with connector (Included)\nCoil option: ATEX EExmIIT4 Temperature Class T4 T130°C Ex mb IIC T4 and Gb Ex mb tb IIIC T130°C Db for hazardous area 21 and 22. \nVoltages: 6vDC, 12vDC, 24vDC, 48vDC, 110vDC and 12vAC, 24vAC, 48vAC, 110vAC and 230vAC.\nIncludes M4x0.8 mounting holes

1355 in stock Model: PU22002AR

1/8 Brass Solenoid Valve 0-8.5 Bar 2/2 Normally Closed 1.5mm PU220AR-01

1/8 Brass solenoid valve Shako PU220AR-01 ®\nFunction: 2/2 way normally closed \nOperation: direct acting\nPort: 1/8 BSP, option NPT thread\nPressure: 0 to 8.5 Bar (AC) or 0 to 7 Bar (DC Voltage)\nBody: Brass\nInternals: stainless steel\nSeals: NBR standard, option FKM, EPDM or HNBR\nOrifice: 1.5 mm\nKv flow factor: 1.2 L/Min based on water with 1 Bar pressure drop.\nMedia: air, water, vacuum, light oils, LPG, diesel, petrol, propane, inert gases, nitrogen, carbon dioxide, argon, oxygen, kerosene, fuel and any other gases and fluids under 40CST that are compatible with the materials of construction.\nCoil: low power 4.5 watt IP65 Class F DIN43650B 100% duty rated\nProtection: IP65 with connector (Included)\nCoil option: ATEX EExmIIT4 Temperature Class T4 T130°C Ex mb IIC T4 and Gb Ex mb tb IIIC T130°C Db for hazardous area 21 and 22. \nVoltages: 6vDC, 12vdc, 24vdc, 48vdc, 110vDC and 12vAC, 24vAC, 48vAC, 110vAC and 230vAC.

884 in stock Model: PU22001AR

Solenoid Coil Core 13.2mm, H 38.7mm, W 36mm, L 47.3mm, 31400

Solenoid valve coil 36mm width, model 31400\nInsulation: Class F 155°C or class H 180°C\nConnection: DIN43650A\nBore: 13.2mm\nHeight: 38.7mm\nWidth: 36mm\nLength: 47.3 mm\nPower DC: 22 to 27 Watts according to voltage.\nPower AC: 26VA holding. \nVoltages: 12vDC, 24vDC, 48vDC, 80vDC and 200vDC or 24vAC, 48vAC, 110vAC or 230vAC 50/60Hz\nResistance: \n12vDC 5Ω\n24vDC 26.6Ω\n110vAC 97Ω\n220vAC 402Ω

768 in stock Model: 31400

3/4 Brass Solenoid Valve 0-8.5 Bar 2/2 Normally Closed PU220A-06

3/4 Brass solenoid valve Shako PU220A-06 ®\nFunction: 2/2 way normally closed\nOperation: assisted lift (zero-rated)\nPort: 3/4 BSP, option NPT thread\nBody: Brass\nInternals: Stainless steel\nPressure: 0 to 8.5 Bar (AC) or 0 to 5 Bar (DC voltage)\nVacuum: 80% vacuum -0.8 Bar Max\nOrifice: 20.0mm\nKv flow factor: 72 L/min based on water with 1 Bar pressure drop\nSeals: NBR standard, option EPDM, Viton and HNBR\nMedia: air, water, vacuum, oil, LPG, diesel, petrol, propane, inert gases, nitrogen, carbon dioxide, argon, oxygen, antifreeze, glycol, kerosene and other fluids under 50 CST and gases compatible with materials of construction.\nMedia temperature: NBR -15°C to +80°C, Viton -10°C to +180°C, HNBR -40°C to +150°C, EPDM -5°C to +130°C.\nCoil: 15 Watt Nass Magnet Class H CE IP65 approved 100% duty rated DIN43650A\nProtection: IP65 with connector (Included)\nCoil option: ATEX EExmIIT4 Temperature Class T4 T130°C Ex mb IIC T4 and Gb Ex mb tb IIIC T130°C Db for hazardous area 21 and 22 with max media temperature +80°C and pressure 3 Bar Max.\nVoltages: 12vDC, 24vDC, 48vDC, 110vDC, 220vDC or 12vAC, 24vAC, 36vAC, 48vAC, 110vAC, 230vAC or 380vAC 50/60hz.\n\nHS Code 8481 8059.

614 in stock Model: PU22006