Search Results

Search results for "-03"

Nass Magnet Coil Core 14.6mm, H 42mm, W 30mm, L 39mm 12v to 380v

Nass Magnet Solenoid Valve Coil System 13/30\nBore: 14.6mm, top plate 10mm\nHeight: 42mm\nWidth: 30mm\nLength: 39mm\nED 100%, Class H, protection according to EN 60529 IP65 with connector.\nConnection: according to: DIN EN 175301803-A\nMaterial: Thermoset resin\nVoltage tolerance: -10% to +10%\nAmbient Temperature: -20°C +50°C\n\nVoltages:\n12vAC 50/60Hz (113-030-0044 or use 12vdc with bridge rectifier connector)\n12vDC 15 Watt 9.7Ω, (113-030-0047, previously 2506442)\n24vAC 19.3VA 6.2 Ω, (113-030-0040, previously 0543 00.1-00/5768, 25002865)\n24vDC 15 Watt 37.8 Ω, (113-030-0028, previously 0543 00.1-00/5753, 2503154).\n48vAC 50/60Hz 19VA 24.3 Ω, (113-030-0052, previously 2507966)\n48vDC 10.9 Watts 20.5 Ω, (113-028-0044)\n64vAC 37.8 Ω\n110vAC 50/60Hz 17.6VA 135 Ω (113-030-0037, Previously 054300.1-00/6869, 2502864)\n110vDC 17 Watts 69 Ω, (113-030-0053, previously 25010353)\n220vDC 18 Watt 338 Ω, (113-030-0051)\n240vAC 50/60Hz, 17.6VA 701 Ω, (113-030-0203)\n380vAC 22VA 2002 Ω, (previously 0543 00.1-00/6755, 25007935)\n\nFits all Shako solenoid 2/2 way 3/8 to 2\" valves: PU220A, PU225A, PU225D, PU225DN, PU225S, PU225H, PU225X, SPU220 and SPU225 series

6281 in stock Model: 22003

Electrical Connector 2P+E Form A without circuit IP65 PG9 0-250v

EN 175301-803 (DIN43650A) square electrical connector without circuit for solenoid valves,\nConnection: DIN ISO4400 Form A DIN 43650A 28mm square\nConduit entry: PG9 (cable 6 to 8mm) or M20x1.5mm with grommet removed\nVoltages: 0 to 250 volts AC/DC\nCurrent: 16 Amp maximum\nCircuit: non\nProtection: IP65\n\n2022 model updated with new terminal block, new reference 611-201-0063\n\nIn order to establish a suitable electrical connection, the use of ferrules for fine stranded cables are mandatory. Be aware that the wire (conductor) cross-section affects the maximum current load (Amp) capacity.

4189 in stock Model: DIN2

Solenoid Coil Core 14.6mm, H 42mm, W 36mm, L 45mm 12 to 230v

24vDC Solenoid Valve Coil Nass Magnet 36mm width\n\nSystem: 13/36 Power Level 5 Class H 180°C\nConnection type: according to DIN EN 175301-803-A, DIN43650A IP65\nMoulding: thermoset resin\nVoltage tolerance: -10% to +10%\nTemperature: -20 °C +50 °C ambient \nRelative duty cycle: 100% \nThermal class: according to DIN VDE 0580 Class H\nProtection: EN 60529 IP65 with connector.\n\nVoltages: \n12vDC/ 36vAC 17.1 / 25VA 8.4 Ω (dual voltage) (113-030-0120)\n24vAC 25VA 4.1 Ω (113-030-0127, previously 0545 00.1-00/5810)\n24vDC 18.5 Watts 30.9 Ω (113-030-0132)\n110vAC 25VA 70.4 Ω (113-030-0137)\n110vDC 17.1 Watts 675 Ω (113-030-0136)\n230vAC 25VA 362 Ω (113-030-0138)\n220vDC 18 Watts 2550 Ω 0545 00.1-00/5889\n\nFits PU220D, PU220A, NOPU220, NOPK and PK series solenoid valves.\n\nCustoms tariff number: 84819000

1641 in stock Model: 22005

1/4 Brass Solenoid Valve 0-150 Bar 2/2 Normally Closed 1.2-5mm

1/4 inch Miniature brass solenoid valve CS Fluid Power AD8000.\nFunction: 2/2 way normally closed\nOperation: direct acting\nPort: 1/4 BSP standard, option NPT or Rc thread.\nPressure: 0 to 150 Bar (depending on orifice and coil power level)\nVacuum: Torr 10-6 Max\nBody: Brass\nInternals: stainless steel\nOrifice: 1.2 mm, 1.6 mm, 2 mm, 3 mm, 4 mm or 5 mm\nKv flow factor: 1 to 9.15 according to orifice, based on water with 1 Bar pressure drop.\nSeals: FKM standard, option EPDM, NBR, Silicone, PTFE, VST, Neoprene, ECO, HNBR or Hypalon. (PTFE must be used for pressures over 30 Bar).\nMedia: air, water, light oils, vacuum, and most other non corrosive fluids under 50CST and gases that are compatible with materials of construction.\nCoil: WPG1 12 watt UL, CSA, CE, IP67 Class H 100% duty rated DIN43650A\nCoil: WPG2 18 Watt UL, CSA, CE and IP67 Class H 100% duty rated\nCoil option: WPA3C 14.3 to 27.5 Watt (according to voltage) IP54 Class H with 30cm flying lead wires 100% duty rated.\nCoil option available AD80**: ATEX EExmIIT4 Temperature Class T4 T130°C Ex mb IIC T4 and Gb Ex mb tb IIIC T130°C Db for hazardous area 21 and 22 Pressure same as 12 Watt WPG1 coil\nVoltages: 12vDC, 24vDC, 48vDC or 24vAC, 48vAC, 110vAC or 230vAC. \nOther options: Manual Over Ride and other custom made options.

1572 in stock Model: AD8000

1/4 Brass Solenoid Valve 0-8.5Bar 2/2 Normally Closed 2.3mm PU220AR-02

1/4 Brass solenoid valve Shako PU220AR-02 ®\nFunction: 2/2 way normally closed \nOperation: direct acting\nPort: 1/4 BSP, option NPT thread\nPressure: 0 to 8.5 Bar (AC) or 0 to 7 Bar (DC Voltage)\nBody: Brass\nInternals: stainless steel\nSeals: NBR standard, option FKM, EPDM or HNBR\nMedia: air, water, vacuum, light oils and any other gases and fluids under 40CST that are compatible with the materials of construction.\nOrifice: 2.3mm\nKv flow factor: 2.0 L/Min based on water with 1 Bar pressure drop.\nCoil: low power 4.5 watt IP65 Class F DIN43650B 100% duty rated\nProtection: IP65 with connector (Included)\nCoil option: ATEX EExmIIT4 Temperature Class T4 T130°C Ex mb IIC T4 and Gb Ex mb tb IIIC T130°C Db for hazardous area 21 and 22. \nVoltages: 6vDC, 12vDC, 24vDC, 48vDC, 110vDC and 12vAC, 24vAC, 48vAC, 110vAC and 230vAC.\nIncludes M4x0.8 mounting holes

1355 in stock Model: PU22002AR