Search Results

Search results for "6000"

Electrical Connector 2P+E Form A without circuit IP65 PG9 0-250v

EN 175301-803 (DIN43650A) square electrical connector without circuit for solenoid valves,\nConnection: DIN ISO4400 Form A DIN 43650A 28mm square\nConduit entry: PG9 (cable 6 to 8mm) or M20x1.5mm with grommet removed\nVoltages: 0 to 250 volts AC/DC\nCurrent: 16 Amp maximum\nCircuit: non\nProtection: IP65\n\n2022 model updated with new terminal block, new reference 611-201-0063\n\nIn order to establish a suitable electrical connection, the use of ferrules for fine stranded cables are mandatory. Be aware that the wire (conductor) cross-section affects the maximum current load (Amp) capacity.

4189 in stock Model: DIN2

Electrical Connector 2P+E Industrial Form B without circuit IP65 0-250v

EN 175301-803 (DIN43650B) Industrial Form Hirschmann Connector, 11mm between pins\nGland: PG9 for cable diameter 6 to 8mm \nVoltage: 0 to 250 Volts\nResistance: 4 mOhm Max\nCurrent: 10 Amps max (without circuit), 1 Amp maximum with circuit. \nConnection: DIN43650B industrial form is with PG9 cable entry for 6 to 8mm\nGasket: NBR\nProtection: IP65\nWire connection: clamping contact. \nOption: conduit entry 5 to 6mm or 1/2 NPT conduit entry, with LED, with VDR varistor and Rectified \n\n2022 new terminal block\n\nIn order to establish a suitable electrical connection, the use of ferrules for fine stranded cables are mandatory. Be aware that the wire (conductor) cross-section affects the maximum current load (Amp) capacity.

2247 in stock Model: DIN1

1/4 Brass Solenoid Valve 0-150 Bar 2/2 Normally Closed 1.2-5mm

1/4 inch Miniature brass solenoid valve CS Fluid Power AD8000.\nFunction: 2/2 way normally closed\nOperation: direct acting\nPort: 1/4 BSP standard, option NPT or Rc thread.\nPressure: 0 to 150 Bar (depending on orifice and coil power level)\nVacuum: Torr 10-6 Max\nBody: Brass\nInternals: stainless steel\nOrifice: 1.2 mm, 1.6 mm, 2 mm, 3 mm, 4 mm or 5 mm\nKv flow factor: 1 to 9.15 according to orifice, based on water with 1 Bar pressure drop.\nSeals: FKM standard, option EPDM, NBR, Silicone, PTFE, VST, Neoprene, ECO, HNBR or Hypalon. (PTFE must be used for pressures over 30 Bar).\nMedia: air, water, light oils, vacuum, and most other non corrosive fluids under 50CST and gases that are compatible with materials of construction.\nCoil: WPG1 12 watt UL, CSA, CE, IP67 Class H 100% duty rated DIN43650A\nCoil: WPG2 18 Watt UL, CSA, CE and IP67 Class H 100% duty rated\nCoil option: WPA3C 14.3 to 27.5 Watt (according to voltage) IP54 Class H with 30cm flying lead wires 100% duty rated.\nCoil option available AD80**: ATEX EExmIIT4 Temperature Class T4 T130°C Ex mb IIC T4 and Gb Ex mb tb IIIC T130°C Db for hazardous area 21 and 22 Pressure same as 12 Watt WPG1 coil\nVoltages: 12vDC, 24vDC, 48vDC or 24vAC, 48vAC, 110vAC or 230vAC. \nOther options: Manual Over Ride and other custom made options.

1572 in stock Model: AD8000

Electrical Connector 2P+E Industrial Form B with LED + VDR IP65 24v 110v 230v

DIN1LEDVDR IP65 EN 175301-803 (DIN43650B) Industrial Form Hirschmann Connector, with Red LED + VDR, 11mm between pins\nGland: PG9 for cable diameter 6mm to 8 mm\nVoltage: 24, 110 or 240 Volt AC/DC\nResistance: 4 mOhm Max\nCurrent: 1 Amp maximum.\nConnection: DIN43650B industrial form is with PG9 cable entry for 6 to 8mm\nGasket: NBR\nProtection: IP65\nWire connection: clamping contact.\nLED and VDR varistor drop off delay max 3mSec power consumption 5mAmp c/w wrong polarity protection\n\n2022 PCB adjusted to the new terminal block, LED will be SMD\n24v 612-201-0100\n230v 612-201-0306\n\nIn order to establish a suitable electrical connection, the use of ferrules for fine stranded cables are mandatory. Be aware that the wire (conductor) cross-section affects the maximum current load (Amp) capacity.

785 in stock Model: DIN1LEDRVDR

Solenoid Coil Core 13.2mm, H 38.7mm, W 36mm, L 47.3mm, 31400

Solenoid valve coil 36mm width, model 31400\nInsulation: Class F 155°C or class H 180°C\nConnection: DIN43650A\nBore: 13.2mm\nHeight: 38.7mm\nWidth: 36mm\nLength: 47.3 mm\nPower DC: 22 to 27 Watts according to voltage.\nPower AC: 26VA holding. \nVoltages: 12vDC, 24vDC, 48vDC, 80vDC and 200vDC or 24vAC, 48vAC, 110vAC or 230vAC 50/60Hz\nResistance: \n12vDC 5Ω\n24vDC 26.6Ω\n110vAC 97Ω\n220vAC 402Ω

768 in stock Model: 31400